Відео

look at your oil light when starting 🤙

Hey man- I think I commented the first time I watched and used this video installing a ZumoXT on my t7, but swapping out my GPS and pulled this back up for some reminder tips on the connections. Great pace, visibility of components and explanation of steps. Thanks again!

great video man super smooth tutorial 🙏🏽 im installing this to my zx10 but wanted to ask, would the black cable go to ground connection ? In your video you put it on the negative side of the battery, and putting on the red cable directly on the positive side of the battery, would that drain the battery ? cheers 🙏🏽🙏🏽🙏🏽

Very well done. No BS, good step by step explanation. Thanks

Just wanted to thank you for the awesome video. Sorry to hear about the hurricane damage, I hope that you've since recovered and are back out on the road. I ended up rolling the excess GPS wire into the empty auxiliary cavity on the right side of the cowl; there is an outlet that allows the cable to spit out right where the empty auxiliary connector is sitting. Again, great video, thank you for passing on the knowledge!

Great video and saved me £50 per hour on labour at Motorcycle Shop. Enjoyed working on the bike as that is part of ownership

Does it came with homologation papers?

Hello, I much appreciate your videos 👍 question what seat is they what you installed. Best greeting from the Netherlands

Grear video!

Tank you for showing all the details!😊

Does 2023 and later vehicles need this airbox mod? Even xsr900?

K&N filter easier to install and take off.

Do they last? Isn’t rain and mud ruining them?

excellent, excellent tutorial! thanks!!

what is the electrical connector I need for this?

Where can I buy the headlight? The link says not available

That was a fantastic video. Very useful - watched this 3 times - helped me a lot. ( I could also see the care you have taken with the high quality video and audio ) Thank you very much 🙏 🙏 🙏

Hey, love the explanation! Is there any reason why I couldn't cut off the yamaha plug and just tie both cables to each other?

very helpfull thanks

The connectors you crimped come from the blank connector? 10min :19sec

Did you have to use a drill press to drill the holes or can you use a regular drill?

code doesnt work anymore

Amount of paste 😮

This was exactly what I needed!! Thanks for sharing!

Can you do all this without remove the plastics???

Great video. Thanks for sharing this.

Will this work on the FZ09 in a legend car?

Has anyone recently bought from Motoinkz? I bought some years ago and they were good but some I bought a few months ago are terrible. Seems quality dipped a lot.

Oggi ho montato le barre, il tuo video è stato di grande aiuto. Come da te indicato ho utilizzato il cric dell'auto sotto la pistra paramotore per mantenere la base allineata.. 🎉grande

People should know that Leovince welds in the baffle, and you have to dremel out the screw... which is close to impossible without destroying the exhaust.

Do they mount with the engine ? Or the frame please?

I'm wondering why the oil that came out from the drain plug hole was black and looked like it needed to be changed, but the oil from the filter clean? - That doesn't make sense to me.

Hello. Is the barkbusters better for wind protection than the stock ones?

Ciao ottimo video. Quindi possibile stringere i dadi anche senza chiave dinamometrica? Grazie

what about Newtons at bolts??

Well done and extremely helpful video. As others have stated, thanks for taking the time making it.👍

nice job man!! did your knees make any attache with the bars when you are riding?? also , when you have the steering wheel at full right or left position does hit the adaptor of bars under the headlight???

If you want to sell the factory parts let me know

Im about to buy them, but I dont know if the basic or bunker version, Do you miss the extra engine protection?

I got the Heed full set of bars for mine, exactly the same procedure only you also need to take out two extra bolts on low point of frame, on left side at low bolts worth cutting cable tie and applying new one once bars fitted. Great quality bars and really easy to fit.

This tool works down and up shifts?

Just watched this. That is unreal. Tuned for the stock settings. I'm thinking about getting the 2024 tracer 9 gt plus or either the mt10. I think I would rather go this route rather than buying a full exhaust and then having a remap done. We'll see.

I've got it....

Great video - i just followed this to instal my heed basic bars and it would have taken waaaaay longer with just the included instructions.

just bought one for my zx14r. went with the top mount kit. cant wait for it to get here. ill be doing more longer distance riding.

Just ordered the same for my WR. How bad is it when touring WITH baffle in? Say anything over 65-70mph?

Nice Job!

one click is enough when using your torque wrench

I just finished up today, had my bars cut and tapped waiting around for 1fngr to come out with their v4 clutch perch/lever. I tapped them by hand with no vice, just drilled the tap until it bit, then worked it with a wrench and a pipe while sitting on the bars. It was a royal pain in the ass but came out way better than I expected. The other pain in the ass was bending that clutch cable housing. Had to break out my trusty pipe again to work that housing straighter, but the wrench and bar threads broke through the electrical tape and marked up the housing. Not the end of the world, though. I appreciate you putting this video together, it really helped. Glad to have the bars on too, they should’ve come like that stock.

Hey nice video mate, just a quick question what could these bars help with? i mean what's the difference between ProTaper bars and stock ones